胜帆GRC安装方法详解

产品名称:胜帆GRC安装方法详解

产品工艺: 

技术参数 


现价:

原价:

在线订购
数量:
-+

胜帆GRC安装方法详解
Shengfan GRC installation method in detail

一、直接安装法:
       直接在建筑原墙上用膨胀螺丝或化学锚栓固定,墙体与产品之间没有其它辅助材料,此法安装方便,快捷,经济。但对建筑本身结构要求非常高,如果空心砖,压气砖等墙体都无法安装,最好是混凝土墙体,另外要求墙体水平垂直精确度比较高,墙平整度比较好。

一、Direct installation method:
        Directly in the building wall with expansion screws or chemical anchor bolt, between the wall and the product without other auxiliary materials, this method is easy to install, fast and economical.But the structure of the building itself is very high, if the hollow brick, air brick and other walls can not be installed, preferably the concrete wall, the other requirements of the vertical and horizontal wall accuracy is relatively high, wall flatness is better.




二、明孔安装法:

       产品表面预留螺丝孔,孔位须加厚,呈内小外大的形状,安装完的螺丝头不能高于产品表面。

二、Ming Kong installation method:
        Product surface set aside the screw hole, hole to be thick, was small outside the shape of large, the installation of the screw head can not be higher than the product surface.



 

三、钢架龙骨焊接法(干挂式):
       此法适用于产品表面,不再另行喷涂或做其它表面处理的产品。根据产品需要或结构需要一般主龙骨用,60*80*4或40*80*4高通。付骨用50*50*5等边角铁,连接产品处的非关键部件可以用40*40*4等边角铁。具体用料大小根据设计要求,但所用钢材必须为热镀锌螺栓及角码等连接件,可以是不锈钢及热镀锌(起防腐,防锈作用)。主龙骨固定于墙体时应在主体结构的梁位或混凝土墙上生根锚固,见图

三、Steel frame keel welding method (dry hanging type):
        This method applies to the product surface, no longer spray or do other surface treatment products.According to the needs of the product or structure need to use the main keel, 60 * 80 * 4 or 40 * 80 * 4 high-pass.Bone with 50 * 50 * 5 equilateral angle iron, connecting the product at the non-key components can be 40 * 40 * 4 equilateral angle iron.Specific material size according to design requirements, but the use of steel must be hot-dip galvanized bolts and angle code and other connectors, can be stainless steel and hot galvanized (from corrosion, rust effect).When the main keel is fixed in the wall, it should be rooted in the beam or concrete wall of the main structure,See Figure :

 

主龙骨固定图
主龙骨固定图、钢板底座示意图

Main keel fixed figure, steel base diagram

 

      如出现特殊状况安装于墙体上的底座,基础空鼓没法固定或不牢固,可采用灌浆处理,将墙面开孔,空位用水泥砂浆灌实方可固定锚栓。产品与龙骨间的连接通过锈钢或热镀锌连接件(标准工艺是直接用连接件上螺丝连接,而我们通常为了方便操作会用焊接法,此做法对要求不高的客户还行)。如果烧焊连接的焊接完后的焊缝一定要做防锈防腐处理,且焊缝的长度至少超过连接件的截面的一半长度,不能有虚焊,焊完后应用小尖锤敲击焊接部位以确定焊接牢固。连接件的连链接分为(一次连接和二次连接)如图:

Such as the emergence of special conditions installed on the wall of the base, the basic hollow can not be fixed or not solid, can be used grouting treatment, the wall openings, empty cement mortar can be fixed before the anchor.The connection between the product and the keel is via a stainless steel or hot-dip galvanized connection (the standard process is connected directly to the screw on the connector, and we usually use the welding method for easy operation).If the weld after welding the weld must be done anti-rust anti-corrosion treatment, and the length of the weld at least half of the length of the cross-section of the connector, can not have Weld, welding after the application of small sharp hammer hit welding parts To determine the welding firm.Connection of the link is divided into (one connection and secondary connection) as shown in Figure :



 

 一次连接焊接法示意图
一次连接焊接法示意图
One connection welding method


二次连接焊接法示意图
二次连接焊接法示意图

Secondary connection welding method

 

------ 责任编辑:胜帆建材
------Editor: Sheng Fan building materials

版权所有http://www.shengfanjc.com(胜帆建材)转载请注明出处
All rights reserved http://www.shengfanjc.com (Sheng Fan building materials) reproduced please indicate the source

 

产品详细

全部评论(0)